Why Does My Hoverboard Only Turn On When Plugged In?

If you have a hoverboard, chances are you’ve run into this annoying problem in the past: your hoverboard will only turn on when it’s plugged in, and won’t start up on its own battery power.

It doesn’t matter if it’s dead flat, or at full charge. It just won’t start up until there is some kind of current coming from the plug itself. I was also stunned when I did not know how to cope with the situation. But, I knew how to surf the internet so I searched through the internet.

Reasons Why Your Self-Balancing Scooter Won’t Power Up

• Bad battery or cell phone – This is a pretty common issue with hoverboards. Most brands don’t specify which brands of batteries they use. Certain batteries won’t work well with some hoverboards. If your self-balancing scooter will turn on when plugged in but not when you push down on it, then your problem might be bad or dead batteries.
• Bad charger or port damage – Charger issues are also fairly common with hoverboards. One thing you can try if your self-balancing scooter won’t turn on is to plug it into a different outlet. You can also try using an alternate charger from another device such as a smartphone (most chargers will fit).

The Battery of the hoverboard might be dead

One of the most common issues plaguing hoverboards (as well as a lot of other devices) is a weak battery. To check whether your hoverboard has a dead battery, unplug it and turn it on.

If nothing happens, then you probably need to charge or replace your battery.

There Is A Short Circuit

Unfortunately, there’s no easy way to fix a short circuit—but it can be a pretty simple fix. The first thing you should do is make sure there are no loose wires. Also, no foreign objects around your hoverboard that might be causing a short circuit.

Once you’ve cleared those things out, all you have to do is determine whether or not your board needs new wiring and batteries. If they are in need of replacement, open up your hoverboard and find instructions online on how to install them (most should come with instructions).

To check if your batteries just need a charge, plug it in and see if it turns on by itself. If it does then unplug it right away before it overcharges!

Low Voltage Issue

Many people assume their hoverboards are broken when they plug them in and nothing happens, but that’s usually not true. In most cases, your device will work as long as you’re plugged into a wall outlet.

If it’s not turning on when plugged in, then there could be an issue with your battery pack (not enough power) or it could be a fault with your charger itself. Another possibility is, there might be something wrong with your charger or battery pack, reach out to customer service to see what can be done.

If they ask you to send it back, make sure you get a tracking number so that you can follow up if anything goes wrong during transit!

Safety Issues

It’s not uncommon for hoverboards to catch fire while they’re in use. In fact, just last year, Amazon banned several brands of hoverboards because of safety concerns.

This isn’t surprising given that many hoverboards were made with cheap components. These were often constructed by unqualified or inexperienced workers. Different parts were often sourced from different suppliers. All it takes is one malfunctioning battery cell to cause a fire.

Even if your hoverboard seems perfectly safe when it’s plugged in, there are still some safety precautions you should take. Never charge your hoverboard overnight. If you plug it in before bed and forget about it. That could potentially lead to an explosion or fire (or worse) during sleep.

Bad Charger

Make sure that you are using a charger that is rated for your hoverboard. The most commonly purchased hoverboards use UL 2272 chargers. They range from 3.7 to 6 volts, and 2 amps to 3 amps.

The label on your hoverboard’s charging port will list what voltage it accepts. So be sure that you’re using a charger with an output rating higher than that listed on your board’s labeling.

Also double-check to make sure there is no dust or hair in contact with either of your device’s charging ports. As even small amounts of debris can affect charge quality.

You Aren’t Connecting It Correctly

One of the biggest reasons hoverboards don’t turn on is that people are trying to charge them in ways that simply won’t work. Most hoverboards have a USB port for charging. It means you need to find a power adapter with a USB output and plug it into an outlet.

If your board has a LED indicator, wait until it changes from red to green before turning on your board (otherwise you risk damaging your battery). This entire process should take no more than 2 hours. It is way easier than trying to use your wall outlet or computer’s USB port.

Dead Remote or Batteries (If you have a Bluetooth Remote Control)

If your hoverboard turns on only when plugged in, then you likely have a dead battery or an issue with your remote control. Both of these issues can be resolved by replacing your batteries or remote control.

Make sure to use quality batteries (e.g., Energizer brand) and check that both your hoverboard’s batteries and remote are fully charged before turning them on for use.

If after replacing either of these components, you still have trouble turning on your hoverboard, there may be a problem with the power switch inside it. Unfortunately, there is no way to fix that from outside of service so you’ll need to take it in for service.

FAQ’s

My hoverboard won’t turn on or charge

If your board won’t turn on or charge, there are a few things you can do to try and get it working. If it is unplugged, check to make sure that you have plugged both ends of your charging cable into their respective ports on your hoverboard.

Next, if you are plugging in while your hoverboard is off. Press and hold both buttons at once until it turns on. If pressing both buttons at once doesn’t work, press one button first then quickly follow up with pressing and holding the other button.

Make sure that all connections between your charger/charger port and your hoverboard are connected properly as well.

How to turn on a hoverboard

This can be difficult to do because there are a variety of different hoverboards that require slightly different actions. Some hoverboards might have a power button on one end and some might have it on one side, which makes them hard to turn on when they’re laying flat.

But if your hoverboard has a power button with an LED light on it (which most models do), then you’ll want to hold down that button for several seconds until it lights up or makes a sound. This means your board is now powered-up and ready for use!

Razor hovertrax troubleshooting

If your Razor Hovertrax hoverboard isn’t turning on, try plugging it into an outlet to see if that fixes things. If you’re seeing red lights, there could be a problem with your battery.

It can take several hours of charging to get a dead battery to 100 percent again, but don’t leave your hovertrax plugged in overnight—it can actually reduce battery life if you do so.

After fully charging, make sure that your device is still working properly. The next thing you want to check is whether or not all of the lights are functioning properly.

The blue light indicates whether or not Bluetooth is working (if applicable) and usually only flickers when pairing with another device.

How do I know if my hoverboard battery is bad?

If your hoverboard battery doesn’t turn on when you try to power it up, odds are good that you need a new one. But before you go shopping for a new battery, there’s one thing you can do to make sure that’s actually the problem.

If it does nothing at all when you plug it in, don’t panic—it probably just needs a charge. If your board has a micro USB port, attach any old smartphone charger to it and wait 15 minutes or so (anywhere from 30-90 minutes is normal). Once charged up, try powering your board on again.

How do I reset my hoverboard sensor?

If your hoverboard only turns on when it is plugged in, there’s a good chance that you have issues with your hover sensor. Sometimes these sensors can be faulty or they could have been tampered with during shipping.

This can cause an issue where your hoverboard only turns on when it is plugged into an electrical outlet. Resetting the sensor isn’t very hard to do and can fix a lot of issues that are caused by faulty sensors. Even someone tampering with them while they were in storage.

Also read: Fix One Side Of Hoverboard Not Working – An Ultimate Solution

Conclusion

If you’re experiencing a sudden decrease in charge capacity, check to make sure that you aren’t over-charging your hoverboard. Most new hoverboards come with 2A chargers. It means they can charge at 2 amps (most other appliances like phones and laptops only charge at 1 amp).

If you keep charging past 4 hours, you might run into trouble. It’s better to leave your hoverboard unplugged for an extra hour or two instead of over-charging. It’s also possible that your hoverboard has a manufacturing defect. It also isn’t compatible with its charger.