Fix Harbor Breeze Ceiling Fan Not Working But Light Works

How to Fix Harbor Breeze Ceiling Fan Not Working But Light Works? Harbor Breeze ceiling fans are some of the most popular ceiling fans on the market today.

Most of these reasons stem from the ability to control the fan with their remote control. It is generally very easy to install them. A few problems can arise with these fans over time that prevents them from working properly, or at all.

The Harbor Breeze ceiling fan not working but the light works are one of those problems that can be frustrating if you’re not prepared to tackle it on your own. I urge you to DIY because our site also teaches us to do it. I am an expert in this field and also want you to be independent.

Check Whether The Power Is On

First, check the power to your ceiling fan. Most harbor breeze Ceiling fans have a light and a switch for the fan. If your light is on but the fan isn’t spinning, then make sure that your breaker hasn’t tripped or blown out.

If you’re sure that everything is turned on and working, then move on to the next step.

Check If There Are Any Broken Wires

If the light works but the fan doesn’t, you should check if any of the wires are broken. You can do this by flipping the switch on and off.

If there is no flickering or change in the operation of the fan, then you have a loose wire somewhere. You will need to locate where it may be and tighten it up.

If your wires are not loose, then your motor is most likely dead.

Listen For the Motor

In the case, you’ve exhausted your troubleshooting efforts and you’re still not getting a response from your ceiling fan, listen for the motor.

If it’s running but the fan blades are not moving, this is a problem with the remote or the receiver.

Otherwise, there may be an issue with the wiring or a faulty switch. It is preferable to call an electrician if the motor is not running.

Lubricate The Blades

This step is a little more difficult because you’ll need to access the blades. First, you’ll need to remove the light kit and fan cover by unscrewing all of the screws that hold it in place.

Next, take out all of the screws on the blade arms. Once you have removed all of these, use a screwdriver or other tool to gently pry off each blade from its slot.

Check For Loose Screws

If you’ve made it through the steps above and your ceiling fan is still not working, then you may have a loose screw. Check for any screws that are not completely tight.

If you find one, tighten it as best you can with a Phillips head screwdriver and see if the ceiling fan starts working again.

Double-Check All Connections

Check that the power cord is firmly plugged into the outlet and that the ceiling fan is not in a position where it could be blocked from receiving power.

Check that all of the connections are tight, and make sure there are no bent or broken blades. If you still experience problems with your ceiling fan after completing these steps, contact a professional for assistance.

Replace The Remote Control Unit

The remote control unit is the part of the fan that gets installed by a professional electrician and it controls the speed and direction of the blades.

It’s possible for the remote to stop working, in which case you can replace it yourself if you have experience in dealing with wiring like this. Otherwise, contact an electrician to get it replaced.

Replace The Remote Control Receiver And/or Batteries

If your Harbor Breeze ceiling fan is not working but the light works. It’s likely that either the remote control receiver or the battery has gone bad. This is a simple fix, and should only take about 10 minutes.

• Turn off power to the ceiling fan at the breaker box (electricity)
• Remove three screws from the bottom of the base housing with a screwdriver to expose the remote control receiver
• Unplug the wires connected to the receiver and remove two retaining screws from top of the receiver
• Slide out the old receiver and replace it with the new one; be sure to put back in two retaining screws on top of the new receiver

FAQ’s

Harbor Breeze ceiling fan reset button?

You must switch the power on and off before pressing the “reset” or “learn” button located inside the remote’s rear cover to reset your Harbor Breeze ceiling fan control.

Hold the reset button down until both the light and ceiling fan speed reaches the middle position.

Why is the Harbor Breeze ceiling fan remote not working?

The main cause of a malfunctioning Harbor Breeze ceiling fan remote can either be a power outage that cleared the memory of the remote. The reason can also be associated with the batteries.

You should eventually change the batteries in the remote. After that re-sync your remote with the receiver to solve all these issues.

• To make sure that the power is on, check the circuit breaker
• Bypass the circuit breaker to cut off the power
• Ensure that the fan blades can freely rotate
• Verify that the reverse switch is not set to neutral
• Make sure all the colored cables are in their proper places, and that the plug connection in the switch housing is firmly fastened

Also Read:  How To Fix Harbor Breeze Ceiling Fan Light Not Working?

Conclusion

A ceiling fan is an important thing to have in your home or office. When it stops working, it can cause a lot of problems.

If your harbor breeze ceiling fan not working but the light works. The first thing you should do is check the power switch. Make sure that the switch is turned on and that the breaker has not been tripped by flipping off a nearby circuit breaker.

Next, look for any visible signs of wear and tear on the blades and ensure they are free from anything obstructing their rotation. Sometimes the motor may be running but there is something blocking its movement – this will prevent it from spinning properly.

Hope so you received detailed guide about how to Fix Harbor Breeze Ceiling Fan Not Working But Light Works.